Peugeot 3008 Key Fob Problems
The mid-sized SUV from Peugeot 3008, has plenty of positive attributes. It's stylish, handles well and has a large boot. But is it capable of beating off strong competition in perhaps the most crowded sector of the market?
If your Peugeot keyfob does not work It could be because it was exposed to soapy or clean tap water. You may need to remove the battery and clean it with electronic cleaner or isopropyl alcohol.
Dead coin battery
Peugeot key fobs are powered by a coin-sized battery. The power used to control the remote locking system, as well as other features. This battery has a finite lifespan and is susceptible to wear out over the course of years of use. One way to determine whether the battery is in good condition is to perform a voltage test. Multimeters are used to measure the voltage between the poles that are plus and minus of the battery. The results of this test will show whether the battery is dead or not.
The receiver module could be the cause of your key fobs not working after using your Peugeot 3008 for a prolonged period. The KeyLab is responsible for receiving radio frequency signals transmitted by key fobs and sending them to car systems. If the receiver module is in an issue, it will not be able to send commands to the other modules in the car.
Sweat or moisture on the circuit board is another typical reason for a malfunctioning key fob. This can cause short circuits that drain the battery, and disable the remote locking feature of the key fob. If this is the case you need to take your key fob in to a chip level technician to fix it.
Water damage
If you dropped your key fob in the pool, threw it in the wash or even left it in the rain for too long, water damage could cause a lot of problems. Water is a good conductor, and can easily short out parts of the circuit board. It can also cause corrosion to metal traces on the key fob and other components. A wet circuit board can also cause the battery discharge its charge.
If you have an extra key fob try using it to lock/unlock your Peugeot 3008 to rule out the possibility that a dead battery is the source of the problem. Interference signals can also cause your key fob to stop working properly. These interfere with the signals sent by the receiver module. These signals can be caused by a variety of sources that include radio transmitters in the vicinity.
If you hear sloshing sounds emanating from the interior of your Peugeot 3008 when driving, it's most likely due to a blocked evaporator condensate drain. You can test for this by taking a look at the drain holes that are underneath your door and blowing compressed gas into them. You can also use flexible metal wire to wiggle drain holes in order to get rid of any dirt that has been accumulating. Air pockets can also be detected by sloshing noises.
Faulty receiver module
The receiver module in the receiver module of a Peugeot 3008 is responsible for transmitting the remote keyless signal from the keyfob to a receiver in the car. If the receiver module is damaged, it could stop the car from recognizing the key fob. Other factors that can trigger this problem include the battery being dead, water damage, or interference from electronic devices operating at the same frequency as the key fob. In these instances the car could display the message "card not detected" on the display.
Luckily, there are a number of ways to troubleshoot this issue. You can try to replace the battery or reprogram the key fob. You can also use a spare key to start the car. However, if the fob isn't functioning after these steps, it might have a chip defective.
The best method to determine whether the key fob has damaged chip is to take it out and clean it with paper towel and rub alcohol. If the chip has been damaged, it is recommended to buy an entirely new one. The FB Series enclosures come with a coin cell battery holder that fits the most popular kinds of key fob batteries. They can also be personalized by using digital printing and CNC machined cutouts. If your key fob was exposed to salted or dirty tap water, it's possible that the chip has been infected.
Faulty keyless entry system
If you receive the message "card not detected" It means that your car cannot receive a signal from your key fob. This can be due to many reasons such as batteries that are weak or dead. The issue is usually resolved by pressing the start button on the key fob. In some cases, you'll be required to take the keyfob to an Peugeot dealer for repairs.
The battery test is the first step in solving the issue with a Peugeot 3008 keyfob which doesn't unlock or lock doors. Batteries are often the cause of malfunctioning keys. However there are other factors that could be involved. These include worn buttons damage to the receiver module, water issues and signal interference.
If you've recently experienced the Peugeot key fob exposed to pure tap water it's a good idea remove the battery and dry the electronic components using paper towels. You can also make use of a cleaner or isopropyl ethanol to do this. It is best to change the fob if it's been exposed salt water or soapy water.
If your key fob is still not working, you can try to reset it by disconnecting the 12 volt battery for about 15 minutes. Connect the negative cable first, then the positive cable.